Propellerhead Reason - 3.0 - Control Surface Details Uživatelská příručka stáhnout pdf (Strana 21)

About the controls:

When you list the X-Station controls in Reason (e.g. when mapping Remote Over-

rides), they will be named according to their labels on the panel. However, in the de-

fault mapping, the name of a control will not always match the parameter it's mapped

to (since Reason has some very different parameters than the X-Station). We have

tried to keep it as logical as possible though.

Many of the controls on the X-Station have multiple functions. When the Reason tem-

plate is selected, the following multiple functions are available:

• In the Oscs-Mixer section, you can select Osc 1 or Osc 2, changing the function

of most knobs and buttons.

• In the Filters section, all controls have different functions depending on whether

you select Filter 1 or 2 (using the button in the upper right corner of the section).

• In the LFOs section, you can select LFO 1 or LFO 2, changing the function of all

controls.

• The function of the controls in the Mod Env/Env 3 section depends on whether

"Mod" or "Env 3" is selected with the button to the right.

• The Velocity slider has three modes, selected with the button next to it. However,

the Trigger and Repeat buttons are not affected by this mode selection.

About the default mapping:

D The transport buttons control the corresponding transport functions in

Reason.

D Reason supports the channel pressure (aftertouch) of the X-Station key-

board, but the result depends on the settings for the controlled device.

D The X/Y touch pad isn't mapped to any parameters by default, but you

can map it freely using Remote Overrides.

Note that there are two control surface items for each axis - you can map the touch

pad to four different Reason parameters (two for the X-axis and two for the Y-axis).

D The Arp On and Arp Latch buttons are used for Target Previous/Next

Track (move master keyboard input up or down in the track list).

D For devices with patches, the Trigger and Repeat buttons select the pre-

vious/next patch.

D With most devices, the Effects Control knob (in the lower right corner of

the panel) controls the master level.

However, for the mixers, the master level is mapped to the Amp Velocity fader.

D For pattern devices (Redrum and Matrix), you select pattern with the but-

tons above the sliders (the four Amp Env buttons and the four first Mod

Env buttons).

The Mod Env F3 button steps through banks.

D With a few devices, keyboard shortcut variations are used.

Peavey

PC 1600x

Requirements/Setting up:

• To use the Peavey PC 1600x with Reason, you need to select preset 21 and make

sure this isn't changed from the factory settings.

• You can reset the PC 1600x to factory default settings by holding down the Utility

and Enter buttons while you turn the power on - note that this will erase all settings

you have made!

• If you prefer to reprogram preset 21 to the default settings (without resetting all

other presets), the faders and buttons should send the following MIDI CC mes-

sages:

Fader 1 : CC 53

Fader 2 : CC 66

Fader 3 : CC 79

Fader 4 : CC 54

Fader 5 : CC 67

Fader 6 : CC 80

Fader 7 : CC 89

Fader 8 : CC 92

Fader 9 : CC 87

Fader 10 : CC 88 (inverted value range)

Fader 11 : CC 55

Fader 12 : CC 68

Fader 13 : CC 81

Fader 14 : CC 56

Fader 15 : CC 69

Fader 16 : CC 82

Button 1-16 : Program Change 0-15

About the default mapping:

D For devices with patches, buttons 15 and 16 select the previous/next

patch.

D For devices with many parameters, keyboard shortcut variations are

used.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26

Komentáře k této Příručce

Žádné komentáře

Propellerhead Reason - 3.0 - Control Surface Details Uživatelská příručka Strana 21

Komentáře k této Příručce